Is there a way to install APK's from any of the bootloader menus? I can install through ADB if the device is fully booted & I have enabled USB Debugging. Is that the only way?
If that IS the only way, is there a way to reset the device's "first boot" attribute back to true after the first boot, so that the manufacturer's setup software runs on the next boot?
View 2 Replies
I bought this device (Galaxy S2 plus i9105p) few days ago.Yesterday I tried my recovery for a first time. There is a red triangle with a exclamation mark and fallen android guy. I can move in my recovery, but anything wont work. For example if I try to do factory reset and confirm it, everything dissapears but the fallen android guy and red triangle.
The phone and android itself works very well.
Is that normal?
Should I try warranty?
I have stock firmware, stock recovery, no root etc.
I have an ICS Tablet Called Xtouch , I bought it yesterday , today , it would get stuck at the blue android logo , and when I press all Buttons + Volume Up , I get into some Asian Text , when I press all buttons and Volume Down , I see a dead Android with his stomach open with a red triangle!
restore it to factory defaults through recovery mode!
I Have An Ainol Novo 7 Crystal Tablet..(Rooted With TWRP Recovery&Cyanogenmod 10.1 Installed).It Was Working Fine Till This Afternoon But I Don't Know What Happened Next..I Turned Off My Device And I Tried To Turn It On Again After Some Time But It Wasn't Booting...
I Don't Even See Any Boot Animation Or Android Logo That My Device Used To Display While Booting,The Screen Of My Device Lights Up Though..And I Can't Even Boot Into Recovery (I Have TWRP Installed),When I Try To Boot Into Recovery I Don't See The Android Logo That I Used To See But The Screen Of My Device Lights Up And Doesn't Boot Into Recovery.. I Tried Removing TWRP Recovery From My sd card And Booting Into Recovery But The Screen Lights Up For Like 5 Seconds And Then The Light Goes Off..
I have an el-cheapo chinese 7" tablet with an Allwiner A20 dual core processor, which I bought off eBay (about tablet read "Wing", but that's about all I can remember).
It has a 512mb RAM and 4gb internal storage. I also have a 32gb TF card.
I thought (for some reason) that putting ClockWork Mod on would be a good idea, if I wanted to flash something like Ubuntu Touch, or CyanogenMod.Unfortunately, I hadn't reallised that the version of Clockwork Mod was not appropriate for this device, and booted to recovery.Needless to say, it didn't even make it that far... It'll only go as far as the very first logo, and no further.
I have 3 Galaxy Player 5 ( YP-G70 with 3 capacitive buttons ), only one of the actually have a working rom that i flashed a while ago.
The other two have a different rom that only have the back and menu button working ( the home button doesn't respond )
Is there a way for me to take the Rom and kernel off the working galaxy player so i can install it into the other two ?
I own HTC Desire which has a built-in GPS. It's a really great option, but what really annoys me is this: when I use GPS, my data connection must also be enabled in order to refresh Google Maps. And since data packets in Croatia are still pretty expensive, this is not a option for me. Anyway, the question is: is there a way to fully download Maps to your SD Card without having data connection enabled, but GPS only?
So, just like with standard GPS devices.
How to distinguish Android is first run or not after booting device?
View 2 Replies View RelatedI make 'hello world' app :-) and wrote a Log code in onCreate. and then give "android.intent.category.DEFAULT" and "android.intent.category.HOME"
This situation appears emulator(1.5, 2.0, 2.1). but HTC hero(1.5, original htc rom) didn't! it just call one time! Which is normal? and If calling twice is normal, why are they call twice?
I rooted my phone back before 2.2 came out. I've played with CWM, made Nandroid and Titanium backups, removed bloat and installed most of the root only apps. What I haven't done yet is flash a ROM. This is mainly because it seems that while there are a crap ton of ROMs being developed out there all of them seem to either not be fully stable or are missing some sort of key feature (camera, videocam, bluetooth, LED, internal storage, etc).
Are there any ROMs that you folks are currently using that's stable and has all the features of the phone working? If not, what's the closest one that you've found?
I have a samsung galaxy young s6312, stock android 4.1.2 jellybean, rooted. I want to install asphalt 8 (about 1.6 gb) on my device. But the problem is that even if I factory reset my device, the maximum free memory I can get is 1.48 gb as my device internal memory is 1.5 gb. I have an external sd card of 8 gb. so how can I install the game with its data DIRECTLY on the external sd? My device is rooted and busybox installed..
View 2 Replies View Relatedhow do i install apks from other devices? i am trying to install sonyericsson timescape on mi700 with no success.
View 1 Replies View RelatedHow to install cyanogenmod in unsupported device (in here i'm using Advan Vandroid E1C [from Indonesia]) ? I had to reading how to port, but i still don't understand how to install it.
View 1 Replies View RelatedI need to instal CyanogenMod 9 or CyanogenMod 10 on RK 3066 device (Cortex A9 Dual Core, 1.6GHz, GPU Mali-400). how to do it?
View 1 Replies View RelatedI have never been able to install Motorola Device Manager on 3 different computers. My problem is just like this Motorola Device Manager won't install!!! except when I click on the link in post #12 (#1 on the list in that post) it says the troubleshooter is not available.
View 2 Replies View RelatedI own an acer liquid mini with custom rom. when I try to install an application from the play store, I get an error: Not enough space on the device. But I have 100Mb of free space. I tried to solve this problem wiped cache, and it worked. So I went to the play store, and I downloaded an app. When it finished the download, I get another error: Package files is invalid. I tried to reflash the rom, wiped cache, wiped delvik cache, wiped all. But the error there is always.When I try to install an .apk on my device, I get this error: "application is not installed".
View 3 Replies View RelatedI have several android tablets, all but one (at this moment) are rooted. I am not interested in putting a custom rom on them at the moment (mainly because not all functions -like camera- are working on all devices) but I would like the ability to do a Nandroid backup that seems to be only available with custom roms. On one device I can't unlock the bootloader (Azpen A701), don't know about the unrooted one at this time (brand new Hisense Sero 7 pro).
Is there a way to add CWM to a rooted stock android (only root applied and associated superuser/busybox apps installed)? What are the requirements (unlocked bootloader?)? Where to get said CWM and how to install it?
I have xperia s (st25a) phone with android 4.0.4.
I already have rooted it (SU installed) and bootloader unlocked. Fastboot reports the correct version "5".
However, when I try to install TWRP, it gives the following error:
>fastboot.exe flash boot stock-6.1.A.0.452-twrp-2.4.0.0.elf
sending 'boot' (8124 KB)...
FAILED (remote: The Device must be rooted first)
Why does TWRP think it's not rooted? I have setup SU to grant every root request too!
Another issue - when I try to enter recovery with stock image, my phone gets stuck on boot with Sony logo and I have to remove battery to shut it down. Why wouldn't stock recovery work?
I'm trying to "install zip from sideload" using ClockworkMod on AT&T Fusion 2.
At the CMD I type: adb sideload cm-10.1-20130602-NIGHTLY-u8665.zip
And get this error: more than one device and emulator
Is it possible to intall Factory Images for Nexus Devices [URL] ..... in any device? I am using Karbonn Titenium S2.
View 4 Replies View RelatedI have a MT6577 Android ICS device. I want to update it to Jelly Bean. How would I do that.
View 1 Replies View Relatedi recently discover that i couldn't install google play services on my phone.when i try to install them it loads up to the end and when it says "Installing..." the following message appears:
"Incompatible with other application(s) using the same shared user ID"
I have recently purchased a pendo pad http:[url].... and it has a getjar apps store on it instead of google play, I have attempted installing the gplay store on the device with the .apk and that didn't work.
View 1 Replies View RelatedMy android tablet will power on, but after the little green guy goes away it goes to the screen where is only says android and it flashes through the letters. After a couple times it wil stop flasing in between the d & the r. Then keeps doing that.
View 3 Replies View RelatedI've attempted to root my girlfriends phone for her so I can unlock it, but the phone just wont root. I've tried superoneclick and a ton of other 1 click roots along with the manual rooting at first (where you go into recovery mode and apply the update from the sd card).
I can see the superuser app, however I cannot grant superuser access to any apps. The version is v2.3.6 and if it makes a difference, it's an irish phone locked to use meteor (a network).
I've also downloaded rootchecker from the play store and it says that I do not have "proper root access to the phone" or something similar. Proper was the predominant word though.Whenever I use superoneclick, the application always freezes as well.
I can do the unlocking half of it myself, I just need root access..Also, when in recovery mode, this comes up in yellow at the bottom.
I did a full wipe of my phone to see If I ccan get rid of cyanogen mod. Now I have no sdcard folder. and I'm stuck in the TWRP menu. Is their anyway of getting my phone back? I have AT&T. I have no android software nothing. but in filemanager It finds a couple folder mostly all empty. Did I void my warranty? Will I never get my phone back?
View 3 Replies View Relatedmy phone is fully charged but cannot boot
it showns this symbol when charing when i unplug,cannot boot
i cant even boot so cannot go into recovery
I recently purchased a Bell Canada version of the SG Note 2 (i317), I am on Telus so I attempted to Unlock the phone. I looked online and found people were having success unlocking these phones for free using the *#197327640# method, (whereby you go into the service mode, turn off the PERSHO_256 and then INITIALLIZ).
I tried this method and the phone then seemed to work with my telus sim, but only for voice, not data. When I put in a Bell SIM from a friend, both voice and data worked fine - which tells me its not a hardware (radio) issue. I also tried using another friends Telus SIM and had the same results as mine - which tells me it's not a SIM error. Also, all the settings in the mobile network area appeared to be correctly set up.
So, my next step was to try and reflash the phone to the stock Bell ROM and then just buy an Unlock code. I downloaded the stock ROM (2 different ones actually) and used Odin 3.07 to reload the ROM. I've tried it several times now, with both Bell ROMs and each time it says it's been successful, but the phone remains in the same, partially unlocked state.
It seems as though by using the PERSHO_256 method I have permanently, PARTIALLY unlocked the phone. I can't seem to re-lock it by installing the stock Bell ROM, and since it's unlocked, I can't get the foreign SIM error to come up to enable me to put in my purchased unlock code.
My specific device is a GSM Galaxy Nexus.
So, I have 3 batteries for my phone. 1 stock (1750mAh) and 2 extended (2000mAh). No I don't need all that juice... its a story for another time. Anyway....
Lately when I charge a battery in the external charger (using a USB cable and the wall plug supplied with the phone) the battery will not fully charge. The LED on the charger will change from red to green (Usually I charge the battery overnight, or while I'm away at work during the day). However when I put the battery in the phone, it will show somewhere between 80%-90% charged.
1) Would a 100% drain and charge reset the battery's "fuel gauge"?
2) My phone automatically powers off at 6% (which is fine, needs enough juice to save current settings and power down properly). Is there a way to truely drain the battery down to 0%? (I'm thinking of some kind of low-voltage lightbulb or LED connected to the positive and negative terminals should drain that down to 0%. Is this recommeneded or is it fine just running it down till the phone powers off?
Normally I try to plug my phone in and charge (or power off and swap batteries) once they hit about 40%-60%. I'm only interested in doing a full drain to see if that will get these batteries to fully charge in the desktop charger. Besides I've read from a few sources that it is GOOD for the battery to do this once in a while (Fully drain, charge to100%) to properly maintain them.
And as a side note, charging the battery in the phone (either with the wall plug or from USB cable on my computer) will always result in a 100% charge, which makes me thing the issue is with the desktop unit itself (perhaps faulty circuit that cuts off charge current when it thinks its full ?)
I purchased an extended battery, a Motorola branded BP7X for a Droid 2 phone. It's rated at 3.7 volts/1820 mAh. I tested it with a volt-ohm meter and got a reading of 4.2 volts.
When I install the battery in the phone and connect the charger (phone is off), the charging graphic shows the battery is fully charged. I can power on the phone with the charger attached, but as soon as the charger is disconnected, the phone dies. I tried this battery in two Droid 2 phones and got the same behaviour. Is this an indication the battery is defective, or is there something I need to do to make the battery work?