General :: Darktremor Get Error After Flash Another Custom ROM Update?
Feb 18, 2012
I've been using darktremor and a2sd GUI, but after I flash the phone GUI a2sd get an error.
A2SD exiting the GUI:
A. your device is not rooted
2. Script A2SD Could not be found
3. EXT no partition found
What should I do?
[Solved] must to mount data, system and ext when you flash a2sd, or if you get a2sd error after flashing custom room take a try to flash new a2sd script..
I use CM7 RC5.5 for galaxy Mini - SquadZone Version
View 1 Replies
Sep 29, 2012
This is the first (and only) time that I have try to root my phone (with the AAHK). After alot of reading I managed to ROOT my Desire HD and it says S-OFF.
The problem is that I am not able to install a costum ROM. I have tried the following roms:
1. Android_Revolution_HD-4G_6.3.3
2. TrickDroid_v2.0.0_C2
And I allways get the same error. It says status 0. I found in some other threads on XDA-devoloppers that the problem is: "Wrong update-binary".
Software information:
Android version: 2.3.3
HTC Sense version: 2.1
Kernel version: 2.6.35.10-gd2564fb
htc-kernel@and18-2#1
Software number: 2.50.405.2
View 1 Replies
View Related
Mar 1, 2010
We can now do partial flashes with the CL14 SBL.... If you have not had the CL14 official update yet, you can follow these steps to get it:
Remember... THIS WILL PUT THE CL14 BOOTLOADER ON YOUR PHONE!
What you need:
Sprints Update Utility
1. Create a datatool back-up.
2. Download and install Sprints Update Utility found above.
3. Run the program (now called SWUpdater) and follow all the directions until it says "Flash Downloading Complete".
Once you have the official CL14 update on your phone, or if you already had it, and you would like to flash SDX/Joey's Kernel (and Max's Recovery), follow the steps below.
What you need:
CL14 official update
An SDX/Joey's Kernel
Max's Recovery
1. Create a datatool back-up... (Although you most likely wont need it if you are just flashing a kernel.... But JUST in case, you should create a datatool back-up if you aren't confident that you wont wipe your data!)
2. After downloading and installing Sprints Update Utility, go into the binary folder (C:Program FilesSamsung ElectronicsSWUpgradeModelsBinary) and move the CL14 file to a safe place, MAKE SURE IT IS NO LONGER IN THE BINARY FOLDER.
3. Find the Kernel you want to flash and put it in the binary folder.
Note: Now you should only have one file in the binary folder (the custom kernel). Also make sure that if the file you are putting into the binary folder says 7zip or winrar, extract it!! If you dont you will get the message "Cannot access bin folder!", and you will not be able to start the download.
4. On your desktop there should be a program named SWUpgrade. Run the program and follow all of the steps through the end. After every thing finishes successfully, you will end up with STOCK CL14, this includes the CL14 SBL, along with the custom kernel you put in the binary folder (you are root).
5. Double check that everything worked by going into Settings-About Phone, under BaseBand version you should see S:M900.8.0S.CL14, under Kernel version= 2.6.27 moment(at)momentdev, under Build number= Joey's name (or any other developer who's kernel you put in the binary folder).
6. Repeat steps 1-4, putting Max's recovery in the binary folder instead of the kernel.
7. You're all set.
(If you happen to want to flash one of Zefie's kernels, repeat steps 1-4 also.)
It wasn't a great thing to get the CL14 update before, because it was hard to obtain root. But now with Sprints Update Utility, and all the new kernels, we are able to get root with the CL14 SBL easily.
View 36 Replies
View Related
Feb 28, 2014
I believe Facebook has updated their Flash requirements, every time I try and watch a video I get a n error message with a "update Adobe Flash Player", I've tried opening the link but it will not download. I have found the Play Store no longer supports Adobe Flash Player so I've tried to manually install the latest android v4.0 software from the archives files but even after installation it still does not let me view. I can view all the videos on my PC without a problem.
View 2 Replies
View Related
Apr 25, 2012
i have a serious problem with my samsung i9001. I can't flash any custom rom..after rebooting i see Samsung logo and then black screen.I've tried moon ROM 1.4 and broodrom rc5..and it didn't work also installing single skyhigh kernel always same problem..black screen after rebooting system after flashing, both by recovery and odin..i have to restore the Android backup to make cell working again.i could only flash stock 2.3.6 value pack rom..this worked.i always do dalvik cache data wipes..
View 3 Replies
View Related
May 3, 2013
I would like to flash the Franco kernel do I need a custom ROM to do it?
Galaxy Nexus using Android
View 5 Replies
View Related
May 26, 2012
I try flashing a kernel but it show this.
FAILED (remote: The Device must be rooted first)
finished. total time: 0.001s
I already rooted my phone so what should I do?
View 3 Replies
View Related
Dec 10, 2013
I have myTab 7 tablet and it's not officially supported device for any recovery. Does it matter? Can I flash any custom recovery e.g. CWM touch recovery or TWRP? Won't it destroy my tablet?
View 1 Replies
View Related
Apr 29, 2014
I just want the device to function again no matter what way. (Don't care if it's factory reset completely it has nothing on it I was just using it for a bit of experimenting).
So anyway, I have an HTC One x that I tried to install Cyanogenmod mod on but when trying to flash it (I was a bit impatient and just did what I thought would work), it didn't work and I'm stuck on the HTC Boot screen. I can still restart the phone and get to the recovery menus or whatever they're called. But even when doing a factory reset it still just won't get past the boot screen.
I thought I might experiment with rooting and all that, (I don't want to do this to my main driver, the Z1, for the life of me).
View 3 Replies
View Related
Mar 21, 2012
Anyway to flash the ics or honeycomb lockscreen on a gingerbread I9001 or any other Phone?
View 2 Replies
View Related
Mar 17, 2013
I used mskip's toolkit to root my device, which succeeded, but I am unable to flash a custom rom. I've tried to flash 2 different versions of paranoid android, using cwm recovery, but I get the following error :
'assert failed: getprop("ro. build. product. device")...
E: Error in /sdcard/0/download/pa_grouper...
(Status 7)
BTW, I had no problems flashing pa to my Nexus 4&10 and loving that rom.
View 6 Replies
View Related
Apr 4, 2012
can i flash it via cwm?
View 1 Replies
View Related
Apr 7, 2014
Can I flash canvas 4 custom rom to xolo q1000s having same cpu?
View 2 Replies
View Related
Mar 13, 2013
I just purchased a cheap 9.7" Android Tablet, Model AM09-D2. It came with ICS 4.0.4, has 16Gb ram and a dual core Cortex A9 CPU. I would like to know how I go about backing this thing up. It is rooted and has absolutely no blootwear installed. Is it possible to flash a custom recovery. Like TWRP or CWM to save a image of the rom. I have already did a data and app backup with Mybackup Pro. Now I would like to backup the Rom and maybe do dump. Is it possible and if so how? Not really that comfortable with ADB/fastboot, truthfully I don't understand what the difference is. I already have drivers setup for Samsung Galaxy Nexus on my Win 8 notebook. Will installing ADB/fastboot screw things up?
View 1 Replies
View Related
Dec 5, 2013
have an iBall Andi 3n here. Runs on MediaTek MT6575 SoC. Getting this error while flashing stock rom.
View 1 Replies
View Related
Jul 1, 2012
I have an AT&T Atrix 4G and I wanted to imstall CM7.2.
I had the latest Atrix Android version on it. Then I followed the instruction at the cyanogemod wiki for the atrix. So I flashed the sbf (cyanodenmod wiki -> Motorola_Atrix_4G:_Full_Update_Guide).
The rsd lite flashing didn't succeed because the atrix rebooted and the programm couldn't switch into BP passtrougth, or so. At this point the device said something about 0x1000 no bootloader, but I could choose between rsd, fastboot and the other possibilities.
I booted into the fastboot mode and did an oem unlock. Now it says unlocked.
I booted again into the fastboot mode, and now it should be a simple
Code:
fastboot flash recovery recover.img
But:
Windows) it always says:
Code:
sending 'recovery' (4824 KB)... OKAY [ 0.453s]
writing 'recovery'... FAILED (status read failed (Too many links))
after that the device reboots and is in a boot loop
so i tried linux) The first time i tried the command everythings worked fine, but after reboot i chose.
Code:
android recovery mode, but after a while (secs) the device rebooted.
so went to fastboot again, but now the device reboots after the sending command and then it says writing failed because of no device
I don't know if when I am using rsd lite to flash a complete image the phone reboots again and i have a hard brick.
View 2 Replies
View Related
Jul 7, 2013
i have clockwork mod recovery v6.0.1.0 and tried to flash Paranoid android 3.6 and then 3.57 both after wiping.
the screen says: Installing.....zip.
Finding update package
opening update pakcge installing update
assert failed: getprop ("ro.product.device")=="grouper" || getprop("ro.build.product")==grouper"
E:Error in ....(blah blah).zip
(status 7)
Installatio aborted.
View 1 Replies
View Related
Sep 24, 2012
I am using Xperia neo V that is running on ics 4.0.4.
Recently I rooted my phone without unlocking bootloader.
Now I need to flash custom rom on to my rooted device with locked bootloader. How can I do it?
View 1 Replies
View Related
Feb 2, 2012
How can i permanently store custom ringtones on root/system partition? if i store custom ringtones on internal or external sd, profiles are messed up every time i connect my phone in mass storage mode.
View 1 Replies
View Related
Jul 12, 2013
I'm new to both xda and android rooting. I just want to know what's the different between Kernel and ROM? Do you need to flash to the latest Kernel to increase stability while running a certain custom ROM? I'm just a bit confused between these two and what their function
View 1 Replies
View Related
Nov 1, 2011
Current issue is that I my phone will boot just fine into regular startup however it will no longer boot into recovery mode.
I have tried the below methods but the main problem that I run into is that when I issue flash_image recovery /sdcard/recovery.img(I have tried multiple img files such as the clockworkmod and SPRecovery) however none of them have worked they are receive the below message.
# flash_image recovery /sdcard/recovery.img
flash_image recovery /sdcard/recovery.img
error scanning partitions
What I need at this point is either a way to get some form of recovery loaded either the out of the box version or clockworkmod version working so I can flash my phone and get gingerbread loaded. Or I need to break the OS to the point where the phone will not load past the boot loader.
Phone information:
Droid 2 Global
System Version 2.4.330.A956.Verizon.en.US
Android Version 2.2
Kernel Version 2.6.32.9-g9e2c63d
What I have looked at so far: [URL] .....
View 2 Replies
View Related
Jan 9, 2013
I'm using a Spice Mi-350 phone (It is the same as Lenovo A60). On the stock Google Maps worked perfectly. But recently i flashed Yonip 5.3.7 Rebirth ROM. Since then Google Maps does not work anymore. When ever i open it, it says 'This application requires a working data connection'. I have a fully working data connection and every other app on my phone can access the internet except for Google Maps and it's related apps(like Navigation,Places,Local,etc).
Here is the download link for the Yonip 5.3.7 Rebirth ROM. [URL] .....
View 8 Replies
View Related
Jan 27, 2014
NEO N003 1/4g T13
I have flashed to newest Stock room from the website neo then i try magerto room he was fine as the beginning then after 2 days he start freezing and sometimes working then the camera is no longer working i tell my self its just poor room
i decide to use the stock room but after i flashed work normal for 10 minute then freeze the screen turn black utile you remove the battery and put back in 2 minutes after many times trying to flash it by sp flash tool i hit format ...my imei is gone and no signal on the sim card ( thats not a big problem)but the phone still freezing and restarting ...black screen ......after that the phone not able to turn on even the logo just black you can see he is trying turn on but no logo no nothing
in the device manager detect MediaTek Usb port before was detect preloader MediaTek somthing ......
look at the picture and the sp tool not working MediaTek Usb port and i got this error
this Morning accidentally i put the phone into Preloader Mode and make normal flash and my phone is a live a was very Happy i went to write the imei must root the phone...i have install root programe name is geno (he is work fine on lenovo P780) but in neo N003 he just freeze and tun off and no longer can trun it on again just black screen.
Now when i plug the phone via usb port windows detect it MediaTek USB Port how i can put it again in Mediatek Preloader VCOM ???Always get error 4032 on sp flash tool (format , upgrade, download) all he same error
View 9 Replies
View Related
Mar 9, 2012
Last week, I played around with getting a custom recovery built for INQ Cloud Touch..
After compiling - flashing recompiling re-flashing for almost a week and on the verge of giving up ...
I realized, searched and found flash_image ... come to find out custom compile of recovery was fine, fastboot did not like my device and wasn't flashing it properly.
So flash_image got the custom recovery working as suppose to, able to backup/restore ... Flash roms.. however there are no roms.. best i could do was try roms from devices close to this one, with no luck!
So i decided i would try my hand at making a 2.3.7 gingerbread rom. Of course stock is froyo 2.2.1 and before i can make the rom.. i need a kernel for gingerbread. So I got the cm-kernel source using this guide:
[URL] .....
[EDIT]
pulled my .config file using both
/proc/config.tgz
and the included script to pull it from the boot.img
[/EDIT]
Now, i been trying to get kernel compiled for the last 5 days.. and like i said, no lack of searching and reading... Had first error, forgot what it was now, but i got it fixed and compile went on.
Code:
LD .tmp_vmlinux1
arm-eabi-ld: no machine record defined
arm-eabi-ld: no machine record defined
arch/arm/mach-msm/built-in.o: In function `parse_tag_msm_partition':
[Code] ......
I have a notepad full of things i have enabled/disabled and restored to original trying to find what is missing or shouldn't be there!
View 5 Replies
View Related
Jun 24, 2013
I tried to flash a custom rom on my huawei honor .. and after I loaded the bootloader.bin by terminal emulator.I restarted my phone and it is stuck on load screen and turn off after seconds. I can't go to recovery mod or anything .. all is what I can do is to go on the pink screen when I press volume up+volume down+ power button
View 6 Replies
View Related
Dec 23, 2013
I bought an S4 clone, Manufacturer alps Model GT-I9500.
I tried with ALL ROM i found, and with GT-I9500_MT6572_ALPS-JB3(fix) ROM without success Even when i wana format or do memory test i get
Code:
BROM ERROR : S_FT_ENABLE_DRAM_FAIL (4032)
[EMI] Enable DRAM fail
View 4 Replies
View Related
Feb 4, 2012
Trying to build a custom rom for the vtab running into error 6. here is what i have and what my script is.
[URL]
All seems correct but yet its erroring 6.
show_progress(1.000000, 32);
format("ext4", "EMMC", "/dev/block/mmcblk0p2");
mount("ext4", "EMMC", "/dev/block/mmcblk0p2", "/system");
mount("MTD", "system", "/system");
package_extract_dir("system", "/system");
symlink("toolbox", "/system/bin/cat");
[code].....
View 3 Replies
View Related
Sep 16, 2013
My phone is dead after I flash a wrong preloader my phone model is alps GT-I9500 mtk6572 . I try with ALL ROM on needrom.com with keyworld "alps" "GT-I9500" "mtk6572" ... about 20 ROM but I get Enable DRAM FAILED for each try
Use case :
1- Disconnet the battery and wait 10 seconds
2- Open flash tools with the scatter file
3- Connect the phone usb cable to pc
4- Plug the batterie on the phone
==> MTK USB PORT (COM XX) ok : drivers on the pc seems to be ok
5- On flash tools press download
every time I get BROM ERROR : S_FT_ENABLE_DRAM_FAIL (4032)
[EMI] Enable DRAM fail
on the web they say the cause is the wrong ROM but I don't know (I try over than 20 ROM)
View 9 Replies
View Related
Feb 17, 2013
how to fix this error... i also create a new scatter file of my phone.. but nothing works..
Error is
EBOOT ERROR : (16008)
[Android Partition size changed!
[HINT] Partial images download error
View 1 Replies
View Related
Mar 1, 2013
I used insecure boot and root trying to root my phone, which was a huge mistake as i noticed a few minutes later since i cant startup anymore and only get into bootloader.
Now I'm trying to flash my stock rom back.
My CID is VODAP102 and my Version is 3.14.161.27 so i downloaded the rom and tried "fastboot flash boot boot.img" the result is:
sending 'boot' <8192 KB>...
FAILED <data transfer failure <Unknown error>>
finished. total time: 0.158s
View 5 Replies
View Related
