General :: Stuck In Odin When Flashing Android 4.0.3?
Apr 15, 2012
I upgraded my Galaxy SII to official android 4.0.3 through Kies one month ago. Unfortunately, it often hang and finally cannot boot up again after my yesterday hard reboot. It stuck in the opening white logo "Samsung Galaxy SII".
So I used "download mode" and followed all the steps, including killing Kies, etc. to flash a new 4.0.3 through Odin. Everything seems working fine before I clicked "Start", e.g. yellow "ID:COM". Only boxes of "Auto Reboot" and "F. Reset Time" were ticked.
However, the installation process got stuck for over 5 hours now as follows:-
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..[code]....
What should I do next?? It seems not appropriate to reboot my device at this moment, but seems no other choice......
View 1 Replies
Jul 5, 2012
Is it possible to flash a zip Rom using Odin? I need to flash a zip. HTC Explorer A310e
View 9 Replies
View Related
Apr 16, 2012
I have new firmware on PC for my Samsung phone, intended for flashing with Odin (i have PHONE, CSC and PIT files). My question here is, is it possible to root this firmware before flashing it. The case is, my phone is now rooted and I don't want to loose root access, but I would like to flash this new firmware, cause with this one i have occasional problems (force close of apps, freezes, loosing wifi connection, etc). I've searched every where but haven't found anything. Only Mobile Odin have such options, but my phone is not supported yet.
View 1 Replies
View Related
Feb 11, 2014
I am stuck in ODIN mode on my Note 3 and it says downloading... do not turn off target. I can boot with volume down and cancel but it just goers their again. Volume up goes to TWRP but i can't get my phone to just turn on normally. I was not attempting anything. This is how my phone turned on...
View 1 Replies
View Related
Aug 26, 2013
SGH-T589R (Samsung gravity Q). I've been trying to flash back to stock rom ever since I rooted my phone. I've used Odin 1.85 and Odin multi downloader but they all get stuck! Odin 1.85 gets stuck at setup connection...I've searched everywhere they all say, try a different computer, try a different usb port, try a different cord, try re-installing the drivers, close kies, run as administrator, uncheck protect ops.
I've even tried this: [URL] ...... The only progress I've ever gotten is Odin multidownloader getting stuck on amss download then boot.img download. Is my phone ruined or is there still a chance to fix it? I am in download mode as I can't get into recovery mode and it says in yellow text "Downloading..."
View 1 Replies
View Related
Apr 4, 2012
Samsung Galaxy Tab GT-P1010 no display got stuck in ODIN while upgrading to GB
View 2 Replies
View Related
Feb 9, 2013
I tried flashing a stock Android 4.2 JB ROM that seems legit. After flashing, I rebooted my device and saw the standard Nexus boot animation. So far, I though all was well. It's not. My phone has been stuck in this constant booting state for hours. I pulled the battery after an appropriate amount of waiting and held down the power and volume down+up button. Instead of booting into Fastboot mode, it went straight to Odin Mode. All I can do with my device is boot to Odin Mode or watch the Nexus boot animation over and over again.
View 1 Replies
View Related
Nov 8, 2010
I want to flash my phone back to android 2.1. My phone is in download mode but odin is not picking it up?
View 3 Replies
View Related
Apr 2, 2010
Has anyone tried flashing the phone from a GNU/Linux box using odin? How safe is it?
I'm using Fedora 12 x86.
View 32 Replies
View Related
Aug 26, 2013
i recently flashed custom roms in my arc s and returned to stock because of the features, when i installed ics 4.0.4 the battery meter is stuck in 100% and the mobile would switch of all of a sudden saying battery is emply i tried deleting battery stats, formatted everything except sd card still no use it is still stuck.. i flashed gingerbread and the battery meter worked fine i was showing the correct percentage, once after i flashed gingerbread charged the battery to 60% and flashed gingerbread it was showing the right percentage... i know the sensor is fine coz its working in gb.. i tried battery calibration and different battery status apps all show 100%. ics once the batterys drained it doesnt charge properly..
View 5 Replies
View Related
Apr 23, 2010
Alright this may have been asked a few times, or maybe it could not of been asked. I just can't find the thread related to answering this question.
Okay so my question is, can I flash Galaxo 1.6.2 or GAOSP "without" ODIN flashing or updating my firmware to 1.6? and not then what consequences would occur if I don't flash firmware update before GALAXO 1.6.2 flash. My phone firmware version is I7500ZHJA1 and I believe that is the latest firmware for my region which is still Android 1.5.
View 13 Replies
View Related
Sep 8, 2010
I was flashing back to stock rom and I followed deaths steps for it, and for about the past hour or so its been stuck, once like every 20 minutes the screen will flash and go back to android. Did I brick it or what?
View 12 Replies
View Related
Apr 29, 2010
I have a Droid Eris that I'm trying to flash from 1.5 to the latest rooted ROM 2.1. My first attempt, I copied PB00IMG.zip to the SD card, disconnected the phone, and flashed the firmware while disconnected from the PC. I think that prevented me from gaining root access, because I cannot remount the system directory using the adb commands (gives me access denied). I'm trying now to flash the ROM while still having the phone connected to the PC, but I'm not having much luck, as I am still being denied access.
PB00IMG.zip worked WONDERFULLY on my phone.
View 17 Replies
View Related
Aug 23, 2010
I just tried to install frankenrom b5 through CWM. It said it loaded fine but I can't exit out of CWM. It kept going from back menu enabled to back menu disabled but the menu never came up. I do know that it is not visible unless I scroll down extra far but no matter what it will not show up. Any help?
View 1 Replies
View Related
Nov 13, 2010
I had an issue flashing the newest version of the leedroid ROM. To start my phone was running stock un-rooted Android 2.1. This is what I've done
1) Rooted the device using the Unrevoked method. Everything with this went fine. I get the Superuser app and I can get the '#' prompt at a terminal.
2) Then I partitioned my SD card using Rom Manager in preparation for A2SD+
3) Then I booted into clockwork mod recovery and wiped data/factory reset, wiped cache, and wiped dalvik cache
4) Then I tried to flash the leedroid rom from zip on the sd card
After reboot my phone appears to be stuck on the HTC screen and will not move forward. But if I take out the battery I can boot back into recovery mode. So it appears my phone is not broken, but it clearly isn't working. I've tried flashing a number of different ROMs but get the same result each time.
View 5 Replies
View Related
Aug 12, 2010
I am following the instructions on the stick from the complete root guide... and i get the the unrevoked flash part and it keeps on getting stuck on flashing recovry image do not touch phone and it just stays there... im not sure whats going on been tryin for a long time now...
View 7 Replies
View Related
Nov 24, 2013
I am trying to flash a custom ROM to my HTC Desire HD.
First I managed to unlock the bootloader using the Easy Ace Root Tool and installed ClockworkMod.
Then I tried flashing a Jelly Beans mod (JellyTime 4.2 R11) and it got stuck at the HTC logo screen. I tried wiping / formatting via ClockworkMod but with no success.
Afterwards I used a second phone to put the Download Android Revolution HD 7.3 ROM on the SD card and flash it. This one went fine through the installation wizard but when I was back to ClockworkMod recovery mode I got: "Can't open /cache/recovery/log" "Can't open /cache/recovery/last_log". Then I selected reboot and it was hanging on the HTC logo again... I was waiting for a minute before I took the battery out... After this I tried "format /cache" from the CWM but didn't work either.
Then I tried using a RUU utility in fastbood mode to flash an official HTC ROM:
RUU_Ace_Sense30_S_HTC_WWE_3.12.405.1_Radio_12.65.6 0.29_26.14.04.28_M_release_225512_signed.
It reached a particular point saying that the update failed.
I thought I cannot install the official ROM because I have unlocked the bootloader, so I locked it again using the htc fastboot utility. This didn't work either and the RUU failed again.
Here is what the bootloader currently shows:
***** RELOCKED *****
ACE PVT SHIP S-ON RL
HBOOT-2.00.0029
MICROP-0438
RADIO-26.14.04.28_M
eMMC-boot
Dec 22 2011, 14:28:19
I have just a couple of shots before this turns into a beautiful piece of aluminium brick.
View 3 Replies
View Related
Nov 19, 2010
I rooted my phone using erisuser1's rooting for dummies method - this went off without a hitch, I followed the instructions to the T. I put several custom ROMs on my SD card (using the USB, and properly ejecting the phone as a drive) including KaosFroyo v37 and v38, CELBFroyo 3.6, PlainJaneT2_V2, and Vanilla_Tazz_19.I tried flashing each of them (following the wipe of the system info and the Dalvik cache) and all but the PlainJane got stuck in bootloops that lasted a long time. I waited anywhere from 15 minutes to a few hours, and none of the others ever loaded up. I'm fine using the PlainJane and happy to have the other features of root but am wondering if there's any advice or suggestions as to why none of the other ROMs worked for me?
View 24 Replies
View Related
Dec 1, 2010
My phone was rooted with the 2.2 firmware everything was working fine and yesterday by itself the phone shut off when i tried to boot it, stays in the samsung galaxy boot screen. I tried going into download by holding vol+home+power but it says POWER RESET or UNKNOWN UPLOAD MODE. The phone is able to connect with my pc I tried flashing 2.2 Froyo with odin3 but its stuck at File analysis. Is there any way to fix this? I cant return the phone I bought it unlocked off ebay.
View 8 Replies
View Related
Sep 27, 2010
For the past 2 hours I have been searching this site and reading about Rooting and Flashing new ROM's etc. and I'm still having trouble. I downloaded Cyanogen 6.0.0 and when the phone re booted it got stuck at the Cyanogen boot animation screen, and when I pulled the Battery and rebooted in to recovery I was able to restore everything and now the phone works again.
So first off, how long should it take after downloading a new ROM to boot back up with the new ROM installed? And how can I save the ROM in to the SD card? And when I go to DL Cyanogen it asks which home application I should use and gives me ADWlauncher and Launcher 2 as options.
View 7 Replies
View Related
Mar 8, 2012
I saw in samfirmware.com that there is already an official Android update for my device. If I download it and use Odin to install, will it erase all data in my phone (contacts, messages, games, etc.)?I know using Kies to update my android will not delete anything...
View 1 Replies
View Related
Oct 21, 2011
I have a rather new phone, 2 weeks at most. I have rooted it, and am now trying to get it on odin. We have two bricked phones to work with, Download mode still works with both. I have dumped all partitions in /dev/block.I am working on the OPS file. I found this in the I believe Odin image. I think it's the OPS but I don't know.
here is the lines cleaned up this is the exact order I found it in from the image.
MIBIB
SIM_SECURE
FSBL
OSBL
NVBACKUP
AMSS
EFS2
APPSBL
DSP1
QDSP_Q
CPFOTA
boot
recovery
parameter
system
userdata
cache
View 2 Replies
View Related
Feb 28, 2012
I have tried everything on my wife's I9001 but I cannot get Odin to get past SetupConnection.Here is a picture:
I have tried:
Redownloading Odin 1.3 and 1.85 and also tried using Multi Downloader 4. (Which says that the .md5 file isn't supported).
Changing USB ports.
Using a Jig to boot Download mode.
Booting into Download mode normally.
Installing MobileODin except that I9001 is not supported.
Trying to flash a different rom other than 'I9001XXKQ1_I9001XXKPI_I9001DBTKP1_HOME.tar.md5'
Rebooting the computer over 9000 times.
Rebooting the phone over 9000 times.
Pulling the battery over 9000 times.
Reinstalling the drivers from Kies.
Turning USB Debugging mode off (was worth a try)
Using a different computer.
Reinstalling my OS (seriously, I had to do that anyway)
Leaving the phone plugged in for 30 minutes anyway just to see if it was working but not updating.
I am unable to boot into 'Recovery Mode' also the phone sh!ts itself and boots into 'RAM Dump' instead... where it requires a battery pull to reboot. So I can't even put the rom file on the internal memory and use recovery mode to flash it from there...
Basically nothing works at all. Odin 1.35 fails, Odin 1.85 fails, Multidownloader fails. I have tried rebooting, restart, and re-bloody everything I can. I have no idea why it won't get past setup connection. I've even tried using my second USB cable. It used to work fine, I used to be able to flash the phone fine.
Kies is NOT running in the background... there are no processes open or anything. I have googled and yahooed and everything to find a solution to this. NOTHING works.. I need to flash this dhfshfgdshgfshs phone as soon as possible. It's not working properly and it's really unstable..
View 6 Replies
View Related
Apr 29, 2013
Does mobile odin support galaxy y?
View 2 Replies
View Related
Apr 8, 2012
is it possible to flash any stock 4.0.3 rom with odin?
View 2 Replies
View Related
Jun 22, 2013
My phone(Samsung Galaxy GT-B5510 (Galaxy Y Pro/Galaxy TXT)) was totally bricked, I couldn't turn wifi on, nothing worked.After I searched some forums I found how to un-brick it by loading the original firmware.
I live in Belgium, and I couldn't find a firmware with the Belgian CSC("PRO"), so I used a Netherlandish-one.Everything went fine and I can use my phone again, everything works, except that the AZERTY-keyboard functions as a QWERTY-one(the default for Netherlands).
Anyways, my phone works fine without a SIM-card. Whenever I try to boot my phone with a SIM inserted, it gets stuck in a bootloop, showing the Samsung-image for about 15 seconds and then rebooting and so on.
So after I thought a bit, I figured out the problem must be that I'm not using a Belgian CSC (my SIM is from Belgium too).
I tried restoring my phone with Samsung Kies, but whenever I click Start upgrade, I get a Chinese error.
However, I have found the location where Kies downloaded the firmware, and the firmware is with a PRO-csc(the one I need), it's located in
C:Users{me}AppDataTempBinaryGT-B5510.
So I tried flashing this Kies-firmware with ODIN, but the problem is that the Kies-firmware has no extension(no .tar.md5 or whatever), so I can't import it with ODIN.What do I do?
View 7 Replies
View Related
Feb 14, 2012
I bricked actually my phone.
I want to know now, wich is actually the best Android 4.0.3 ROM.
I know how to flash via zip and via odin.
I dont know how to flash kernel
I wanna use a Android 4.0.3 ROM with DarkKnights or Siyah Kernel, tell me what you think about it.
First flash the ROM then Kernel?
View 6 Replies
View Related
Nov 12, 2012
So, my question: Is it possible to turn a rom from Odin format (.tar/.tar.md5 etc) into a flashable zip? If yes, how?
My intention was to customize a stock rom for the gt-s7500, with dsixda's kitchen, that apparently supports only flashable zips.
View 1 Replies
View Related
Jul 18, 2013
im trying to root my Gs3 i747!! My usb mini port got bad so i got it replaced and now it wont connect to computer! not even in download mode it doesnt even show the icon on notifications. I tried framaroot, Ezinox abuse, root Z4, thru terminal with motochopper method and nothing!! my gs3 is 6 months old but i lost warranty, My only chance to build a method for the i747 gs3
View 9 Replies
View Related
Apr 18, 2012
I have a question about the files being used to flash my Samsung Galaxy S2 via Odin.
I have already seen this link [URL]...
I am trying to flash the PDA, Phone and CSC back all to normal stock. I have downloaded a firmware and I only have one file with a .dll file. The one file I have is named "I9100BOKK1_I9100TMUKK1_I9100BOKJ1_HOME.tar.md 5" I have extracted the files from here also and it contains boot.bin, cache.img, factoryfs.img, hidden.img, modem.bin, param.lfs, Sbl.bin and zImage.
How with these files and Odin do I flash all three parts. I can't see how to use these files on the above link with instructions for flashing and rooting.
View 1 Replies
View Related
