Motorola Droid :: New Baseband Update
Jun 7, 2010Thought this needed its own thread as its already buried in the froyo thread.

Thought this needed its own thread as its already buried in the froyo thread.
UPDATE - The file can now be found here:
http://mydroidfiles.com/downloads/basebandupdate.zip
OP
-----------------------------
That's right folks,
This was the goodie that I wanted from the OTA update the most, and now, thanks to t3hSteve at Alldroid, it is available to us in update.zip form. Confirmed success with Clockwork recovery, and I have done it as well with SPRecovery 0.99.3b.
You WILL be prompted to reactivate your phone, and also, re-enter your Google password.
Link:
Baseband results anyone? Bueller?
Screenshot:
Additionally, I would suggest you reenter your programming menu (dial ##PROGRAM) to change your vocode to EVRC-B.
The SPC password is 000000
Tired of losing your 3G on the new baseband? Dropping signals and calls all the time since the OTA update? Well here's the solution! The Baseband Downgrade to .01P!
1) rename to update.zip
2) place on root of sdcard
3) reboot into SPR
4) choose Install
5) Allow installation from update.zip
6) Install
7) Re-Activate by dialing *228, option 1
Baseband update for your froyo 2.2
View 35 Replies View RelatedHow to I install Baseband update (C_01.43.01P) currently showing in CW under Bugless Beast. Tried once without wiping. Do I need to wipe... again. Stuck on Moto icon now.
View 15 Replies View RelatedI was running NexFro 1.01 but due to alot of buggyness on my phone I had to abandon it and go back to NextBeastvs 1.1 on firmware 2.1.
After which my reception went to hell even after I did a *228,2. So I tried to install the baseband update .43.01 from the link located here:
http://androidforums.com/all-things-root-droid/121527-what-baseband-everyone.html
However it just error's out when I try to install from the SD card using lockwork, says Installation aborted.
Does this baseband only work for 2.2? If so what is the best one for firmware 2.1?
If you have received the 2.1 OTA from Verizon, can you tell us your baseband version, kernel, build #, and software #.
Just to compare those to the 2.1v3 leak to see if they're the same.
with all the baseband's out right now, and all the questions as which one to run, perhaps it would be a good idea to post which one you are using, have used and your findings. i am on 01.43.01p. it has the fastest 3g speeds for me. i tried 01.41.00r but didnt get as good of a reception.
View 48 Replies View RelatedWhats the best baseband out right now to use with froyo roms i dont want anything that has known issues.
View 15 Replies View Relatedexperts and newbies. What is the 3p baseband? What do we benefit from it? What baseband are we currently running? I have a Motorola Droid.
View 2 Replies View RelatedI have been looking at the baseband threads and I am thinking adout trying a new one. Mine is still the stock one. Should I try use Pete's. All in one? I also see it depends some on your location.
View 12 Replies View RelatedJust wanting to know what the current baseband for the 2.2 release is. I'm terrible with searches and can't seem to find it.
View 3 Replies View RelatedEver since manually updated the baseband on my phone my service where i use the phone the most has been horrible my Perl also changed when doing this so i dont know if thats the reason or the baseband its self Ive tried countless times to update my Perl but it doesn't change any ideas on what i can do to improve my service by either getting new Perl or change baseband back
View 11 Replies View RelatedI'm on NexFro v1.0 baseband C_01.43.01P (2nd froyo baseband leak) now and my signal is bad. Can I downgrade to C_01.41.01P (1st froyo baseband leak)? Everything was ok with C_01.41.01P. Or do I downgrade to the one before that? What should I do and how should I do whatever it is I need to do.
View 2 Replies View RelatedWhen it Rains, it Pours: Newest Radio File for the Motorola Droid C_01.43.01P you must have the C.01.41.00R baseband to upgrade to this one.
View 49 Replies View Related"-Baseband Version VS740MVB.5210.1015: (new radio.img) Flash this just like a kernel. You must reboot into recovery once more after installing to wipe your cache. *Only flash once! I cannot be held liable for any damage caused to your device by flashing this!" If you back rev to Velocity 0.2 from Velocity 0.3, do you need to redo the Baseband update, or is it permanent?
View 20 Replies View RelatedI am running Nexbeast 1.1 so not a Froyo ROM, but I did update to the latest baseband via Pete's install on the ROM manager. Everything works great and my signal is usually 3-4 bars everywhere so it is a small improvement there.... However, I've noticed that my downloads have slowed dramatically. I used to get around 1.25Mb down or at least routinely over 1Mb, but now it's barelly 500-600k each time. I'm in different areas of town and it's not any better. Has anyone noticed this problem?The other thing is if I wanted to revert to the previous baseband (not the 3E.03P but rather 3E.01P, I believe) where do I get the file?
View 13 Replies View Relatedwipe baseband data - what does it do?
View 10 Replies View RelatedDo I have to wipe data and cache just to install my new baseband? I really dont wanna have to go through the steps to get my phone back to the way it is now.
View 2 Replies View RelatedI haven't found one yet but is there any Froyo ROMs with built in baseband updates to .43?
View 8 Replies View RelatedI did a baseband update and it wasn't working i it.restarted my phone and no i have no bars. What do i do to fix this?
View 5 Replies View RelatedI updated baseband using recovery and everything went well. Afterwords, it appears to be messing with my temps. Previous to update SetCpu would consistently show temps in the 20's. Now it is almost always @ 30 or above. But Tempmonitor shows differently. Here are some pics. Any Ideas?
View 7 Replies View RelatedI'm currently running RubiX Focused 1.0 on top of the leaked 2.3.15. I was thinking of SBF'ing to the 2.2 OTA to get the updated Radio and Baseband. My question is this, once I SBF, root and install Bootstrap, can I then Nandroid back to my RubiX?
View 6 Replies View RelatedI had bought an X off craigslist where the guy had updated to the leaked 2.2 build. i wanted to go back to stock 2.1 and i want to confirm i was successful. i was in the infinite boot loop by the way.
Anyways, here are my stats:
System version: Version.1.13.604.MB810.Verizon.en.US
firmware: 2.1-update1
baseband: BP_C_01.09.04P
Kernel: 2.6.29 w30471@il93lnxdroid08 #1
Build number: VZW
ERI version: 5
PRL version: 51926
So am i bone stock or did i mess something up?
Might someone on the official 2.2 OTA look at what their baseband and kernel version is and post it here. I just updated but want to confirm that I got the full update and not just the system files.
View 4 Replies View RelatedI was looking at the OTA ZIP file from VZW and noticed some BIN and IMG files. I'm guessing that it bootloader and baseband images. Is there a way that I can swap out those files with a nicer bootloader? Basicly what I want is stock OTA 2.2 with 29.01 or 30.01 bootloader but I want the new baseband with the update. Can I do this or does it just fail because of signatures, checksums, or some other crap I can't think of?
View 13 Replies View RelatedI'm currently running the CM6 rom on my DINC, and I guess I forgot to update my baseband version, which is preventing me from using WiFi, and my camcorder function. So I downloaded the baseband update.zip, and put it on the root of my microSD, formatted in fat32 btw. Hboot detects the update.zip, but for whatever reason can't install it. When I go into ClockworkMod Recovery, and choose the apply sdcard:update.zip option, after 'Writing RDL/BP image..." I get the error "E:Error in /sdcard/update.zip (status 0) Installation aborted".
View 4 Replies View RelatedI just recently updated my phone from the 2.1 that came stock on my incredible to CyanogenMod 6.0.1 (i didn't do 6.0.2 because it gave me com.android.email errors) this was my phone on stock 2.1 (BEFORE i updated anything)
Code:..........
I'm on C_01.3B.01p
could this be causing my bad battery?
The newest Sprint HTC Hero maintenance update from 11/19/10 also added a new radio baseband update. The version number is 2.42.02.10.29.
UPDATED 11/26/10: xda-developers - View Single Post - [ROM] NFX-Sprint.STOCK.2.32.651.2.ODEX.A2SD Updated:11/23/2010