General :: Touchlet X10 / Unable To Get Into Flash Mode / CWM Recovery
Apr 6, 2014
I recently bought a Pearl Touchlet X10 quad core (PX-8880-675) tablet, but it was full of mods and when i plugged in the charger i received the "plugged in, not charging" message. So i started to clean up the ROM. Finally it showed charging, but now i really messed it up, beacuse now it is not booting. The tablet was not factory software, another tablet software on it that has a volume rocker. To start the flash mode i need the volume up button, but this version of tablet does not have this button. I tried the home button version, but it is not working because of the different firmware.
Here's the thing:The tablet always starts recovery mode, no screen, but adb working. When i type "ls /dev/block" in ADB shell it shows loop0-loop7 and nandf, so it is not seeing the nand I have seen other forums that when I type "dd if=/dev/zero of=/dev/block/nanda" it will erase the nand, and the tablet is force booting into fel mode (flash mode), but it not erasing beacuse the recovery is not for this tablet and it not seeing the nand.
View 2 Replies
Apr 24, 2012
I deleted /system folder on my nexian cosmic journey. And now my nexian is stuck...
I try to using fastboot mode to flash recovery image, but my device seems not detected. I already installed the android composite driver, but when i use "fastboot devices" command, it shows (?) So how the heck to get my nexian back to normal?..
Or perhaps, if i just be able to put back the /system folder to its place again, it would be more easy to recover it... But how access the root when phone is like that?
View 1 Replies
View Related
Apr 20, 2014
I'm following step by step process to root my gt-s5310 using ODIN 3.07. Started from download mode and connect to the PC is no problem at all. ODIN finished with the GREEN PASS. When I tried to open recovery mode, only android recovery mode is open(but malfunctioning, going no where when I press the home button) that recovery mode also don't has "install zip from sd card" option.
My android version is 4.1.2 . Baseband version S5310DXAME2. Kernel version 3.0.15-1521875 se.infra@SWDA2309#1
Attached is the recovery mode picture
View 5 Replies
View Related
Jan 26, 2013
i am not able enter flash mode in my X10i device i wanted to flash kernel.
I followed all the procedure:
1) by holding back button & plugged in USB cable.
2) my phone got recognized in the flash tool. Got a message stating "Device connected in flash mode"
3) then my device did not stay much longer in flash mode (less then 10 sec). After that it automatically booted to phone charging screen.
below is log generated in flash tool, when i tried to flash the kernel:
26/026/2013 07:26:07 - INFO - Selected kCernel-CM9-v03.ftf
26/026/2013 07:26:07 - INFO - Preparing files for flashing
26/026/2013 07:26:07 - INFO - Please connect your device into flashmode.
[Code]....
View 2 Replies
View Related
Mar 19, 2012
I am using sony ericsson x10 mini mobile phone. I want to install custom ROM cyanogen 7 gingerbread. But I am facing problem while booting this in recovery mode. I have tried the following.
downloaded custom rom for xperia mini and copied in to sdcard
installed ROM Manager Premium (not purchased, downloaded from google search and it is working fine)
installed root explorer S1 tool
Rooted from superoneclick
downloaded xRecovery and copied into system folder
Flash tool - showing bootloader unlocked, and dont know how to flash phone.
msm7227 - used for unlock boot loader
I have rooted my phone successfully, all above things did successfully, when i am trying to boot my phone into recovery mode then it is not boot in that mode instead it boots in normal mode. What I am doing when phone starts and sonyericcson appears then i continuously pushing button many times but it boots in normal mode. So what I have to do to boot my phone in recovery mode. I have read and tried many guides in your forum but nothing works.
View 7 Replies
View Related
Oct 11, 2013
I have a ZEN ultrafone 701 HD (MTK 6589) device with HD screen.
Things were going fine when this Fine day I got a bright idea to change ROM.
I have a rooted Phone with working CWM, so went into recovery and cleared data/cache/dalvik cache,battery log etc.
Then I did a epic goof up by clicking on the ROM file of a different device to install as ZIP from CWM . by the time i realized, it was too late Now the phone boots up, shows logo and reboots,again and again. a previously working key combination to bring diagnostic mode is now not working.
The phone starts up and reboots so fast the PC cannot detect the device in adb mode. perfect aint it ?
View 9 Replies
View Related
Feb 27, 2014
I've got a Chinese phone Pomp W89 and I wanted to put a custom rom on it, I tried to install cwm and twrp but I've found out they don't support my device, so I went on needrom and found a recovery file for my phone which I downloaded and used rom manager to flash.
But I've then worked out the file was corrupted and since then I can't get into recovery mode the phone just showed a brief white screen then boots up normally, it does say recovery mode at the bottom but never goes into it, I then found a complete recovery file for my phone and flashed that but the same thing happens without the brief white screen just a black one then it boots up normally.
I've tried cwm to flash and several other programs and I also then tried the terminal emulator to flash which I think was successful but the exact same thing happens, I just don't understand if the new recovery.img has been flashed why would nothing change? There was already a recovery.img on the phone which I kept a copy of and that makes no difference either.
I was going to flash using my computer but I have windows 8 and can't get the usb drivers to install for the phone.
View 1 Replies
View Related
Nov 14, 2010
Ok i have not been able to find any answers what so ever regarding the people that can not find the backup/restore option after entering the recovery mode. I have recently rooted using the new z4root application. I get a skull and crossbones supper user app, and was wondering if that means its different than the one with the ninja icon that everyone else gets.
Anyways, When i go to make a nandroid back up, i follow the steps to the letter, but when i get to the recovery menu, my options stop after the wipe baseband data option. there is absolutely nothing else there that says anything about backup/restore option everyone seems to be screaming about. Its not there!
Now please can someone figure out a solution to this problem?
My recovery looks like as follows: Android system recovery <3e>
Use d-pad to highlight: center to select.
reboot system now
apply sdcard:update.zip
wipe data/factory reset
wipe cache partition
wipe baseband data
View 3 Replies
View Related
Apr 3, 2014
Friends of Jupiter Huawei g525-u00and have been asked Ram Kastvm able but Alanmshkl. Already green screen after power ... not that fast boot mode will not go into recovery mode and not the original ROM using loam bottom half Vbala White gets going
View 5 Replies
View Related
Apr 15, 2014
I have a Samsung Galaxy S Plus where, after flashing CWM with Odin, and installing cm11, I'm stuck on an infinite boot animation. But that is not the big issue. I need to enter Recovery Mode, where I have a backup, but the problem is that my Volume Up button is not working, so I can't use the Power Button and Volume Up(I also don't know what could possibly wrong with it) one to get there. So I was wondering if there is some other method to enter Recovery, I suppose by computer. I think that when I used Odin, the device restarted being in Download Mode, and I think that it hasn't to be On to do that.
View 1 Replies
View Related
Oct 7, 2012
I guess as I rooted my att GS3 just fine and flashed a new aokp rom and was up and running but started to have intermittent flickering. It prompted me to reflash rom with CM10 and this is were my problems began. I wiped data/factory reset, cache partition,Dalvik cache, mounts & storage format cache, and accidentally format emmc which I think is my problem. I was able to still reboot to CWM recovery but I can't do much more than that, and now I can't get to CWM recovery mode at all. Have tried to boot and reflash from ex/sdcard no good. PC doesn't recognize phone to do recovery from backup and I didn't do internal backup which I now know was dumb. Is there anything I can do to get back up and running or did I screw myself and have to get a new phone?
View 1 Replies
View Related
Sep 13, 2013
I have a Nabi 2 tablet that I've rooted, installed TWRP, and flash the gapps and a few other tweaks to. It's about to go in for an RMA since the USB and charging ports are both broken. The problem in the USB port is that one of the pins got bent - I don't know how, it looks like the conductor somehow got peeled back off of the plastic. The point is, I have no USB access to the device.
In order to pass the inspection for the RMA, I need to have it stock I can flash the stock ROM by putting it on the SDCard in my laptop then transferring that to the device and flashing it through TWRP. The question I have, though, is whether I can flash the stock recovery with ADB access to it. Every thread I've been able to uncover so far about flashing a recovery requires ADB access to issue the "adb fastboot flash" command. Is there another way to do this?
View 9 Replies
View Related
Sep 26, 2011
I just rooted my Nexus S and it was successful.
However, now when I try to install Cyanogenmod I can't get into recovery?? When I go into bootloader, at the bottom it says "Fastboot Status - FAILInvailed Command". And when I click on Recovery, the Google logo shows up with an unlocked image below it. It flashes a few times and then reboots the phone regularly.
View 5 Replies
View Related
May 26, 2014
i have rooted my karbonn A7+ successfully after that i did a big mistake... i have flashed rom without CWM recovery..i did this=> opened power button + volume up key for recovery mode and applied direct rom through the option apply update from sd card in result i found that my mobile got stuck on boot animation.. after that i've cleared user data and wipe partition chache and now its showing BLUE SCREEN only .
View 1 Replies
View Related
Jul 25, 2013
I've just bought an Oppo phone (with MTK6589 chipset.) 2 days ago I decided to root and flash CWM recovery to my phone. Rooting gone well and the phone is now rooted. Then I flashed CWM with Mobile Uncle Tool. It said that I flashed sucessfully, I got no error. But when I reboot the phone to recovery mode, nothing happend, the phone just did a normal reboot! I tried to flash other third-party recovery mode such as TWRP and MIUI recovery but I got the same problem: the phone couldn't get into recovery. The screen with a text "Recovery mode" appeared in 3s and the phone just did a normal reboot. I couldn't even format factory, all I got was just a normal reboot. I even tried many tools on Google Play and MTK flashtool but there were no hope. Now my phone is working normally but can't get into recovery mode.
View 2 Replies
View Related
Sep 12, 2013
how to enter Recovery Mode holding down volume up AND volume down and press power.
View 1 Replies
View Related
Oct 23, 2013
I Have Android MTK6575 with Android 2.3.6
its called " G-TiDE E60 "
before doing anything , when i enter the recovery mode it shows a picture of an Android and a Triangle next to it " Which should be the background image of the recovery mode " and there's no menus or anything , nothing appears even if i press power or volume buttons
So now after i rooted the phone , installed another recovery.img with MobileUncle , it just keeps stuck on the phone's logo and doesnt even show that triangle picture and it doesnt show anything but the phone's logo
I tried a lot of different recovery.img files but none worked, Then I tried a recovery img that worked for another guy who has the same mobile kind , it worked for him but didnt work for me
Even after flashing it with MobileUncle , still i get the same problem..
All what i edited in the root files was the boot sound and animation and i even restored the stock ones back and still the same problem
and the last_log file in System(Root)/cache/recovery Includes this
Starting recovery on Tue Oct 15 04:49:44 2013
framebuffer:
0 /Imp rarrellsk (null) (null)
1 /boot mttl boot (null)
2 /cache yaffs2 .cbe (null)
3 /data yaffs2 user.. (null)
4 /mlsc mtd mlsc (null)
5 /recovery mtd recovery (null) /scl.rd vfat /clekeblack/mmcblkOpl /clekeblaclUmmcblk0 7 /system 540s2 system (null)
PS : Oct 15 is the last day i ran the stock recovery that only shows up the background image of recovery .. So all the recovery runs after flashing new recoveries till Oct 23 arent logged in last_log..
View 2 Replies
View Related
Mar 21, 2013
I want to make a clean hard reset of my GoClever Tab R974.2 but no matter what I do it won't load the bootloader. I tried all pssible combinations of all 3 abailable buttons (power,vol+,vol-) and all possible pressing times from a few seconds to a minute.I also tried rebooting into bootloader via the ADB but without any luck (device not recognized).My main problem with this system is that I tried to root it and it seemed like it worked, the superuser .apk was installed, however when I tried to start Titanium backup or any other prog that requires root access, it shows that there is no root access. Then I also tried z4root, but no luck either and SuperOneClick just freezes when restaring the ADB daemon.
View 1 Replies
View Related
Oct 7, 2012
I got the root for the Panasonic P-01D then deleted many preinstall app, such as launcher and android keyboard,so don't have any launcher and keyboard after reset the phone(wipe phone data).Now only can connect the phone to adb in recovery mode, because no root and launcher to open the usb debug.Can i install any launcher to phone in recovery mode by using adb?
View 9 Replies
View Related
May 30, 2012
Need rooting my gooapple 4gs. I have tryed everthing. And i can't access the recovery mode. volume key + power, dont work.
View 3 Replies
View Related
Mar 24, 2013
I've got an a31 allwinner device. (novo 9 spark)After having rooted it, i can't exit from recovery mode: adb device shows me a number and recovery...And the tablet doesn't want to boot normally.
I can't use phoenixsuit, because it's now not recognised by the pc (recovery mode).
View 3 Replies
View Related
Mar 5, 2010
I was rooted and decided to unroot for giggles. After i did I went to root again and now I am getting this: "E: cant open/cache/recovery,command " When I reboot into recovery mode.
View 4 Replies
View Related
Feb 21, 2012
I tried to flash CWM Recovery but when the 'confirm your device' menu popped up, my phone wasn't there so i just selected the first one on the list. Now when i try to reboot into recovery, nothing happens. It just boots up normally. how to either flash stock recovery or a custom recovery that will work?
View 1 Replies
View Related
Oct 29, 2012
My phone is on CM9.. i want to revert it in stock rom. my computer doesnt detect my Phone when emergency mode even i have drivers installed.
Is there a way to flash my Phone with the CWM recovery with the stock rom? .kdz file?
View 1 Replies
View Related
Dec 10, 2013
I have myTab 7 tablet and it's not officially supported device for any recovery. Does it matter? Can I flash any custom recovery e.g. CWM touch recovery or TWRP? Won't it destroy my tablet?
View 1 Replies
View Related
Jan 28, 2014
1. Can recovery flash bootloader?
From this link====>[URL] ....., I think it can do that. But I'm not sure.
2. Can recovery flash recovery partition itself?
I think it can not do this. Not confirm that.
3. We know in update.zip, boot.img is corresponding boot partition, but why system is a folder, not system.img? There is a system partition also.
4. While OTA upgrade system, why the update package downloaded under /cache path? Can we change it to sdcard?
5. Most important, what exactly update-script do things under recovery mode? How the command executed?
BTW, there are other questions, but not related to Recovery Mode.
1. How can I see the flash partitions? I know to use the command cat /proc/mtd, but as Samsung, it use emmc flash, while I type that command, no results printed. How to see?
2. About userdata partition, we know that when first run android OS, system will copy files from /system to /data, but does it do it every time that we turn on the phone or just do it once after the first booting after we update our system?
View 5 Replies
View Related
Aug 9, 2010
I hit the top button. Flash Clockworkmod recovery or what ever it said. I then backed up my Current ROM. I then downloaded Cyanogen v6.0.0 cr2. It downloaded and rebooted my phone. But It went to a screen with a Triangle w/ exclamation and a phone under it. I then hit the up vol button and camera, and now I'm at the Android system recovery page and I don't know what to do next. These are my options reboot system now apply sdcard:update.zip wipe data/factory rest wipe cache partition wipe base band data. I did click to backup current ROM and wipe data and cache.
View 38 Replies
View Related
Aug 28, 2010
Just FYI in case anyone wants to know: For download mode, with the phone turned off, fold the number 1 key on the QWERTY keyboard and the power button simultaneously For recovery mode, with the phone turned off, hold Volume Down, CAmera, and Power simultaneously. You navigate with volume UP/DOWN, select with HOME, Menu toggles to "Manual Mode", whatever that it.
View 3 Replies
View Related
May 14, 2013
I have an Android tablet (Diablotek D2-721, very cheap I know, but it serves its purpose) that is stuck in a boot loop. The real problem here is that this device apparently does not have any sort of recovery mode and being in a boot loop means it does not get recognized by ADB or any firmware flashing software.
I researched all day yesterday perusing forum after forum but almost every single solution requires booting into recovery.
View 1 Replies
View Related
Jul 1, 2013
I recently rooted my LG Optimus L3-8C (E400) running stock rom and version 2.3.6 Gingerbread (yuck) and I followed all the instructions from this video:
in order to flash the CM9 ROM. Problem is I can NOT reboot into recovery no matter what I do it seems. When I try tp reflash the CWM recovery it tells me "successfully installed!" then when I press 'reboot into recovery" it gets stuck on the LG logo for so long I often have to hold the power button to go back to my device. I even download "recovery flasher utility" found here [URL]....but, whenever I run the app it tells me "no recovery.img" found onexternal SDCARD even though I placed it there! I tried to fastboot but whenever I run CMD it tells me " 'fastboot is not recognized."
View 3 Replies
View Related
