How is the operating system getting these numbers? If I'm using 2+ GB on Rdio alone, how am I below 2gb of data during the month so far? I'm on Solavei so I have 4gb of 4g before it gets throttled and it would suck to get throttled and have no idea how much data I've actually used.
View 2 Replies
I'm looking for a tutorial to Root and then revert back to JellyBean from KitKat on a Nexus 7 2013 2nd Gen, non carrier, WiFi only, or Whatever is required to switch back to JB from KK..
View 1 Replies View RelatedI have a Be.SOCIAL SC020 with Android 4.1.2, which has two SIM slots.
I want to make sure that SIM2 never, ever connects to the Internet, though I do want to use it for calls and SMSs.
Under Settings, I can't find any setting for enabling/disabling data completely per-sim. (There is an option for enabling/disabling data *roaming* per sim). There _is_ a setting under Data Usage for putting a limit for data consumption: there you can set a warning threshold and a limit. However, while the warning can be set to 0MB, the lowest value you can set for the limit is 1MB (I know, so stupid...).
Up to now, I haven't detected any data usage on sim2, but my fear is that at any moment when the data network for sim1 may become temporarily unavailable for any reason, sim2 may be used for data. Even if I have set the 1MB limit, sim2's operator will charge me a fixed amount per week if I use non-zero data.
So how do I disable data completely for sim2 while keeping data enabled for sim1 and keeping sim2 enabled for voice and sms?
I seem to have a problem I have rooted and unlocked my bootloader and flased with rom Carbon 4.3.1on my HTC HD Desire Phone. Everything runs fine except the data don't seem to work even though the correct settings has been applied. Whats so weird it comes on for like an hour then don't come back on again. I have had the rom installed for like 3 days now and it has come 4 times. I have tried switching off the phone, trying different settings also my mum and bro have the same network and same apn settings in my phone is in theres. The apn settings work fine in the stock rom.
Edit - Also I will like to add that the data flickers on and off. The H sign next to the bars
I first noticed this maybe late last week where my phone would appear to have data (bars and the 3g/4g symbol) but not actually being able to connect to things. I'd enable and disable airplane mode to reset things and it would work for awhile.
Yesterday, I contacted Sprint about this because it is fairly annoying. While paying closer attention, I started noticing that my data worked with 4G but would not with 3G. In Settings -> More Networks -> Mobile Networks - > Network Mode: I changed it from LTE/CDMA to CDMA. When the phone rebooted, I was on 3G and the data worked. When I changed it back to LTE/CDMA 4G would work but 3G would not. I've also tried Automatic and 4G works but 3G does not. Needless to say, I spent an hour with customer support and their best solution was to just leave it in CDMA mode. When I complained that I'd lose my 4G service, the tech asked for my zip code and after a moment told me 4G was unavailable in my area. I've been using it for more than 6 months, was using it today, and have seen the sensorly maps showing 4G availability......
It definitely seems like a phone issue over a network issue because the 3G network is clearly working if I can use it when I've disabled LTE. The most annoying/frustrating issue is that the phone claims to have 3G but nothing works.
Phone: Samsung Galaxy S4
Provider: Sprint
Android Version: 4.3
With android 4.1 on my Galaxy S3 I could select an image in the gallery, tap the menu and choose settings where I could find the exif data, but since upgrading to 4.3 the settings option is missing. So how do I now pull up the exif, notably the gps coordinates, on the phone?
View 1 Replies View RelatedSometimes when I start playstore, it shows that "Background Data is disabled".
How it get disabled and how can I keep it enabled all the time.
I am using Mobile Data.
This problem does not occurs when using wifi.
My os is 4.3.
I m using Samsung S3.
I bought an ATT S3, running android 4.1.2. I set up the APN as instructed by straight talk and everything works except data... just can't connect to the internet. On my old sprint S3, there is an option to turn data on and off in the top menu bar (when you swipe downwards from the top of the screen), but this option does not exist on this phone. There are buttons for wifi, bluetooth, gps, etc but NO DATA! At first I was thinking it was the APN settings, but now I am thinking there is something else wrong because I don't even see the data button to toggle it on or off. I can't see incorrect APN settings preventing the toggle data option from even showing on the phone.
View 5 Replies View RelatedI have a Coolpad 8720L with its own interface built upon 4.3 Jelly Bean. It's not very good, and I'd like to install stock Android instead. How do I do this?
I heard that I have to root the device, and then find a ROM for stock Jelly Bean to load onto the device?
My phone updated last night and afterwards I've been experiencing problems. I had 6 apps in the bottom bar including the apps button and I was forced to remove one so the others would fit. My main concern is that my mobile data on off switch in the notification bar is no longer there.
View 2 Replies View RelatedJust wondering what would be better/more accurate for a data usage counter...
View 6 Replies View RelatedI just purchased my first ever cell phone ( Google LG Nexus 4 16gb ) . I have never used one before , just never had the need for one . How to use Android Jelly Bean 4.3 and also how to use this phone .
View 5 Replies View RelatedBest way I could describe it. On ICS the dialer would allow me to type a number and come back to it later, now when I multi-task the number disappears. I am running 4.1.2 on a HTC Desire 300, and the dialer is stock to the best of my knowledge.
View 4 Replies View RelatedThe jellybean box itself turns on and the home screen loads up. I select the page where all the apps are...select xbmc app...sometimes it flicks back to main apps page other times the screen turns black/blank. I can't get further than this page....my box has worked perfectly for the past 3 months since purchasing. I can't get into the settings page as I can't get past the blank .
View 1 Replies View RelatedHaving issues with Tapatalk returning an incorrect username/password for XDA while on data? This issue only presents itself while trying to access XDA on data, no such problem on wifi, or for any of the other forums I frequent whether on data or wifi.
View 4 Replies View RelatedIs there an app that allows you to see how much data you have used, sms messages you have sent and how many calls you have made? An all-in-one app is what I am looking for.
View 6 Replies View RelatedAwaiting delivery of my Nexus 4 - 16GB, is there software to back up the phone data to my PC?
View 3 Replies View RelatedMy bro has a note running jb. He has a secgallery app which I cant install on my xperia u wid ics
I always get an error "App not installed".
I have decompiled the app... But m nt a modder so I dun knw what changes to make in androidmanifest or some other folder to run it..
After I flashed a couple roms I couldn't boot jelly bean anymore and I noticed the error in recovery: E: Cant Mount /efs, when installing. But I could still boot ICS but not jellybean. I still had my IMEI and could make calls but could not boot jelly bean because it couldn't mount.
Sometimes when installing a rom something goes wrong and it changes the partition type of /efs making it unable to be mounted. The partition is usually from ext4 to swap.Most likely this will work on your phone but if it doesn't and your phone stops working I am not responsible.
If your like me and you couldn't get jelly bean to work then flash your device back to ics and it should boot. Once your booted inside of ics we can start the process.
Pre-Setup:
1. Be rooted and have a custom recovery installed.
2. Be on Ics and it boots.
3. Your need to have a Jelly Bean rom like Cyanogenmod on your sdcard.
4. Have adb installed on your pc and usb debugging on in your phone/tab.
Now that that's done its time to start.
Part One:
1. Boot into recovery.
2. We need to find the efs block location.
3. Go to mounts and select efs
4. It should say unable to mount
5. Go to advance and make a recovery.log
6. Put that file on your computer and open it.
7. Look through the file and you should fine something like this around the beginning of the file:
E:Unable to mount '/efs'..Actual block device: '/dev/block/mmcblk0p3', current file system: 'swap'..My location is /dev/block/mmcblk0p3 But yours could be different! Most likely the difference will be instead of it ending with a 3 it will be a different number. I will be saying /dev/block/mmcblk0p3 if yours is different just change it to your location.
*WARNING* Sometimes when you copy paste into adb it will auto run the command without you pressing enter. If your location is different then mine and you copy past and it auto runs it could be BAD so to be careful if you want to copy past. Copy the command paste it into Google make the change and copy that and paste into adb
Part Two:
1. When your inside recovery connect your phone to your computer and get into a adb shell. (Sometimes it will take awhile for adb to recognize your device so be patient.)
2. Once you have adb access its time to start entering the commands.(Again my location may be different the yours! Most likely the difference will be instead of it ending with a 3 it will be a different number.
Part Three Inside ADB:
1. su
2. dd if=/dev/block/mmcblk0p3 of=/sdcard/efs.img
3. mke2fs /dev/block/mmcblk0p3
4. mkdir /efs
5. mount -t ext4 /dev/block/mmcblk0p3 /efs
DONT REBOOT PHONE
Part Four On Your Phone:
1. Now /efs is mounted don't unmount it
2. Do a factory reset
3. Install your Jelly Bean rom
4. It should install without any errors
5. Boot your phone
6. If everything went well it should boot.
7. After it boots your signal notification most likely will be gray and internet or calls may not work
8. To fix just install gapps and it will be fixed
There you have it if everything went correctly your efs should be working good and you should be able to go back and do your normal rom flashing.
If jelly bean boots but you don't have phone do this:
1. Go back into recovery and get adb access.
2. su
3. mke2fs /dev/block/mmcblk0p3
4. mkdir /efs
5. mount -t ext4 /dev/block/mmcblk0p3 /efs
6. dd if=/sdcard/efs.img of=/dev/block/mmcblk0p3 bs=4096
I just recently bought the Samsung Galaxy S II on the Straight Talk network. The phone comes stock with the Android Gingerbread 2.3.6 OS and I'd like to upgrade to the latest Android Jelly Bean 4.2 OS.
Here are the phone facts:
Network: Straight-Talk
Model Number: SGH-S959G
Android Version: 2.3.6
Kernal Version: 2.6.35.7
Build Number: GINGERBREAD.UDLG1
I came across a thread to get Jellybean animations on ICS, I did a search but I cannot find it. HTC Vision
View 1 Replies View RelatedI've got an replacement of my karbonn A2+ via company.
I want its backup and flash file..
Is it possible to upgrade HTC One V to Jellybean 4.2?I have tried running software update located in settings-->about phone but it says that there are no updates available.So is it possible to get jellybean 4.2 on my phone?Are there any risks involved?Can updating to jellybean harm my phone?btw my phone is rooted. What cyanogen mod is?Can i first install jellybean 4.2 and then install cyanogen mod?
View 1 Replies View Relatedim trying to port crt off and on ..on deodex'd stock rom..i had try'd these methods but it didnt work'd out on jelly bean..link for porting crt off on stock jelly bean rom for GT-i9082
i had try'd these methods but no use..
[URL]
I've attempted to build two different sources, one modified ICS AOSP and another from straight up JB AOSP. Both err on me.
JB spits out the following:
Quote:
make: *** No rule to make target `out/target/product/devicetest/obj/STATIC_LIBRARIES/lib_driver_cmd_wext_intermediates/export_includes', needed by `out/target/product/devicetest/obj/EXECUTABLES/wpa_supplicant_intermediates/import_includes'. Stop.
make: *** Waiting for unfinished jobs....
target thumb C: wpa_cli <= external/wpa_supplicant_8/wpa_supplicant/src/utils/edit.c
I'd prefer to get JB working, but would be satisfied with ICS for now.
Running RemICS-JB on my infuse, hotmail won't connect. Tried using m.hotmail.com and debug-m.hotmail.com and neither worked.
View 2 Replies View RelatedThere must be a way of checking data usage on the phone without recourse to an app; the app gets its data from somewhere on phone and presumably repackages it so its all user friendly and easy to see etc. I could dispense with the 3G watchdog altogether (just cutting widgets down) if I knew where it was. Is it the packet figure in *#4636.?
View 2 Replies View RelatedI'm looking to find jelly bean 4.1.1.
link to where I might be able to download this version?
i recently updated from ics to jelly bean 4.1.2 on my Samsung galaxy s2 on 02 uk network, i have noticed a few different issues since the update though regarding blocking calls and i notice the feature isnt as good since the update
previously on ics when blocking a number, once a number called they would be present with "dud a duh sound" which made the phone sound like the number was disconnected it would also not divert the blocked number to the voice mail
since doing a test on jelly bean when blocking a number, it now diverts them to the voice mail, and what's more annoying is once a blocked number calls it seems to one ring on my phone and then divert them to the voice mail, similar to as if i was cancelling there call every time, which is no were near as effective
ive just tried an app called mr number and this is the same, although this does have the option of a "hangup feature" and a send to "voicemail feature" again when the blocked number calls it seems to one ring and then either be disconnected or diverted to the voicemail, which again is like your cancelling there call every time after one ring
on ics when blocking the number they were never presented with the ring tone on there end, they were only presented with the sound of a disconnected line etc. How i can get that feature back???, without using mr number which doesn't do it as well
id like it to be like it was with ics, so basically the blocked number doesn't even get the chance to to be diverted to voice mail or to be not connected at all??? and certainly so it doesnt one ring on my end before the divert/block kicks in, on ics the blocked number never got that far, it was blocked instantly and presented with the disconnected sound, and then i was shown on my phone a log they had attempted to call., i also dont want to give the impression im cancelling the call on my end, as like ics, this was a good feature as certain people would just think your unreachable, know when a blocked contact calls with the new system under jelly bean it looks like your cancelling there call everytime after a one ring.
also is it still not possible to block text messages from certain spam numbers?
Has successfully established a bridge mode VPN connection (using TAP) in any version of Jellybean, stock or custom?
It seems that every vpn app in the play store suggests that this can't be done in JB. I'd really like to upgrade to JB, but I really don't feel like reconfiguring my whole VPN setup, just to log on to my home server every once in awhile.