General :: Allwinner A13 Q88 Tablet - How To Add Drivers To ROM
Dec 24, 2013
I cannot find out how to add drivers to a ROM
I don't have a backup of the stock ROM, however i have a ROM in which everything apart from WiFi works ( 5 point touch screen, all hardware buttons, sound, screen)
This Q88 ROM is downloaded from [URL] .....
I tried the cyanogenmod ROM from ANONFBI [URL] ..... and nothing works apart from the wifi driver no touch, no volume buttons
I would like to extract the drivers from the q88 rom and add them to the cyanogenmod rom.
I've never been able to get the camera working its the single front camera it doesn't bother me its not very good
I tried this thread [URL] .....
However when i load a driver the ported PORTED JB-4.1.1 rom doesn't boot up
I see it has camera drivers but i dont know how to install them
I have attached a LSMOD from the q88 rom
View 4 Replies
Jun 12, 2013
I want to get a custum recovery because I can't access to my recovery mode it shows a foto of a droid, I tried rebooting from rom manager app, and from the power and Vol+ .. but nothing works you can check the foto in the attachments.
View 3 Replies
View Related
Apr 19, 2012
Is CWM available for the Eken T01? I have posted this question several times on other boards and never got an answer either way. I just got this tablet and I have rooted it. However I would really like to make backups with CWM like I do with my phone because it has saved my butt more than once
View 9 Replies
View Related
Jun 7, 2014
I have an Allwinner A31s based tablet and I can root when i use Android 4.2.2.
Couple of weeks before my tablet producer relase Android Kitkat Rom
Old method for rooting Android 4.2.2, dosen't work on Kitkat.
How can I root my Allwinner A31s based tablet on Android Kitkat?
View 1 Replies
View Related
Oct 6, 2013
i have a allwinner a13 tablet that has gotten stuck in the process of opening. i had installed clockmodrecovery and uberizer. and was looking for a way to correct root 'permission" that kept coming up when trying to install programs that needed root access. then i messed up.
i was trying to restore factory when it froze. i cannot use buttons to enter recovery mode. i made a back up in uberizer but am unable to find .how to use. also since this is happened i cannot load any driver to recognize the tablet into windoes 7device manager.
View 2 Replies
View Related
Apr 20, 2014
I received a generic Chinese table. it worked well for about two-and-a-half months. Then, just recently, I discovered rooting and the wonderful things it allowed you to do. I decided to download a system-tweak app, which included a CPU control. I was a little wary of overclocking my CPU, having heard it may decrease its life expectancy, but finally I thought "What the heck?" and in a brilliant stroke of genius cranked my 1Ghz processor up to 1.5Ghz, and it promptly froze, forcing me to power it down. When I turned it back on, I discovered that it had been factory reset. I re-installed my apps, including the system-tweak app, and decided not to touch the CPU controls for a while. Soon after, while at my sister's talent show, I discovered I had about 30% battery life, and I was still supposed to record her. So I figured I'd underclock it to save the battery.
Unfortunately, as my finger touched the slider, my brother bumped my arm and caused me to lower the CPU frequency to its lowest setting. It became extremely sluggish, almost to the point of being unresponsive, and finally I had to shut it down. When I restarted it, it started to boot but then got stuck on the shimmering Android logo, and now that's all it does. I can't even boot into recovery mode, and unfortunately I had just turned off USB debugging that same day.
View 3 Replies
View Related
Feb 6, 2013
I have a generic Allwinner A13 7" tablet essentially identical to this one. The internal memory is set so that part of it is seen as internal, and part as a fake SD card mounted on /mnt/sdcard. Actual SD cards get mounted to /mnt/extsd.
I find this very annoying for a number of reasons, and would like all the internal memory to be seen as internal with no fake SD cards, and SD cards to be mounted to /mnt/sdcard. If this were one of those tablets capable of running Linux I'd run gparted and do the job from there, but it isn't.
Is there any way to merge the two internal memory partitions into just one?
I'm aware I can edit vold.fstab and invert the two mount points, and I'll keep it as a fallback solution, but I hate the idea of wasting a gig of useful internal space like that.
View 2 Replies
View Related
Mar 1, 2013
My problem is as follows: I'm having trouble rooting one of my customer's Android tablets (DIT 1010) version 4.0.3 and kernel version 3.0.8. (As far as I can tell there's no custom skin)
From what I've gathered Android knows 3 modes and ADB mode is the one that has to be active for me to be able to root it. However Windows stops recognizing the tablet once I've enabled USB debugging.
I've tried installing google android drivers, didn't work. I kept digging and found out I had to manually add my tablet's device ID to the .inf file. I tried this but still no dice. To be more specific these are the lines I've added (Without the Google.NTx86 and Google.NTamd64 lines, they're just for clarity):
[Google.NTx86]
; Android ADB Interface
%SingleAdbInterface%= USB_Install, USBVID_2207&PID_0006
%CompositeAdbInterface%= USB_Install, USBVID_2207&PID_0006&REV_0222
[Google.NTamd64]
; Android ADB Interface
%SingleAdbInterface%= USB_Install, USBVID_2207&PID_0006
%CompositeAdbInterface%= USB_Install, USBVID_2207&PID_0006&REV_0222
I can't really find anything about this tablet and apparently the ADB drivers are device specific.
View 1 Replies
View Related
Dec 9, 2012
Tablet hangs in Bootloop after installed cm9_nightly_20120721 + protab2xxl_compatibility_1.2.0 startet from cwm 6.0.1.0. Noticed that the "/data" partition only has 15MB of Space with 0B Byte free. I wiped the cache after installation with cwm, i am not able to boot to cwm again because key combinations not work on this device.
Got a T15A Generic tablet which has the same Hardware than protab 2 xxl, Goclever A103, Coby 1042 etc..how to get CM9 or CM10 running?
Code:
--------- beginning of /dev/log/main
I/cm ( 70): Welcome to Android 4.0.4 / CyanogenMod-9-20120721-UNOFFICIAL-907
I/cm ( 71): _
I/cm ( 72): __ __ _ ___ _ _ __ ___ __ _ _ _ _ __ __))
I/cm ( 73): ((_ (/'((_( ((( ((_)((_( (('((( ((`1( ((_)((_(
[code]....
View 2 Replies
View Related
Oct 6, 2012
is it possible to port a cm7 for allwinner a10 tablets??
View 1 Replies
View Related
Jul 9, 2013
I recently acquired an A13 tablet and wanting to install CM10 on it I first installed CWM 6.0.2.8 according to the famous manual (if it's relevant I'll post the exact url). Anyway, it got stuck on CWM (doesn't boot normally). Now I figured it can't install since using 'adb shell' and looking at /proc/partitions -- nothing is there!
"""
cat /proc/partitions
major minor #blocks name
179 0 15558144 mmcblk0
179 1 15554048 mmcblk0p1
"""
So I have no internal memory to use -- no internal memory to install to, right?
"""
ls /dev/block
loop0 loop2 loop4 loop6 mmcblk0 nandf ram0
loop1 loop3 loop5 loop7 mmcblk0p1 platform ram1
"""
Seems that only nandf exists, which means I can't cat into nandg and sync and install new img. Right? Or am I missing something? How do I fix this?
View 9 Replies
View Related
Jun 26, 2013
I am trying to use my cheap virtually unbrickable tablet to learn more about kernel development and eventually ROM building.
I have extracted the manufacturers (WoPad) LiveSuit image and used split_bootimg.pl to break up the boot image.
I extracted the config file from the kernel image using extract-ikconfig and it created a config file. I didn't see the config in /proc.
So, I have the factory ramdisk and the factory kernel config.
I have downloaded several kernel sources (lichee-3.0.8, ChritianTroy's 3.0.36, and another one from linux-sunxi 3.0.72). I can successfully compile all of them without errors and they all generate zImages, uImages, etc using the factory config as well as the sun4i_crane configs they come with.
When I repack the boot.img with the newly created kernel and install it on nandc it wont' boot past the android icon (u-boot). When I compare my boot.img to the factory one, they both have the same offset where the kernel starts (0x00000800). I have also ensured I'm replacing the kernel modules when I'm changing kernel versions.
Here is the line I'm using to repack the boot.img
Code:
mkbootimg --base 0x40000000 --pagesize 2048 --kernel zImage --ramdisk ramdisk-repack.cpio.gz --board sun4i --cmdline "console=ttyS0,115200 rw init=/init loglevel=8" -o boot.img
[Code]...
Also, I'm building on Ubuntu 13.04 with Google GCC 4.6 from the ndk. I have built kernels for other devices without issues.
View 3 Replies
View Related
Oct 20, 2013
caused & am now stuck in a recovery boot loop.
- bought a Thomson QM734-8G tablet (Allwinner A13b clone), running Jellybean 4.2.2;
- PC interface worked fine in MTP and large storage modes;
- setup Android SDK & Java JDK on PC and communicate with tablet via ADB;
All OK so far..After a couple of days, I decided to replace stock recovery with ClockworkMod Recovery, so I could start messing about with the tablet.
I found the CWM 6.0.2.8 mod supposed to work with these tablets and, following instructions, determined it was indeed running on sun5i hardware and had 10 partitions (nandj) and downloaded the appropriate version.
I used ADB sideload to install CWM and everything appeared to work OK ... until I rebooted and found myself stuck in a never-ending cycle of CWM-based recovery bootloop.All I get is the CWM recovery console, with a few lines of error & the tablet will go no further.
E:can't mount /cache/recovery/command
E:cant mount /cache/recovery/log
E:cant open /cache/recovery/log
E:cant mount /cache/recovery/last_log
E:cant open /cache/recovery/last_log
CWM functions work properly and nothing will mount through the 'Mounts and Storage' section, although sideload mode still seems to work.Attempts to use ADB sideload to install a different CWM or other recovery image have all failed, and LiveSuit and PhoenixSuit both have issues detecting the tablet (despite trying various versions of each & following instructions precisely), so I can't flash a replacement ROM to fix things.
At the moment, I just want to rip CWM out and go back to factory recovery mode and have a working tablet again! I think the Bootloader is locked and the tablet is unrooted. Superuser or SuperSU don't want to install properly. However, using ADB, it looks like I can get root access in shell (#).
View 9 Replies
View Related
Sep 15, 2013
I own a Allwinner A13 7 inch tablet, on which I installed the Cyanogen 10 mod (Due to restrictions I cannot place the link to the mod)
The problem is I probably installed the wrong touchscreen driver, so the tablet boots perfectly into the Mod but I can't do anything. Normally it would be no problem to just put back my backup, but I can't get it to boot into CWM.
In the first place I rebooted into CWM to instal the mod by adding the following command through the "terminal app" before rebooting,
Command: "echo -e 'boot-recovery' > /dev/block/nandf; sync"
Now I cannot use the screen so i cant use the terminal. I also cannot use ADB because USB debugging is standard switched of after flashing a new MOD. Any other way to get into CWM??
View 3 Replies
View Related
Jul 31, 2013
Basically I ran Livesuit to flash my Chinese Tab, its called a desiretab has an a10 processor. Anyways the first flash was successful, besides the fact that it didn't pick up touch calibration correctly. So, I decided to flash it again with a different firmware image, low and behold it gets about 50% in and just freezes up. Now the Tablet shows no form of screen output, I attempt to flash it repeatedly, nothing works.
When I say I attempt to re flash it and nothing works, I'm saying that it just sticks at zero and the flash command does nothing.
View 1 Replies
View Related
Jan 13, 2014
I using Onda v975s (chip Allwinner A31s). In Android 4.2.2 i can root it. But when i up to rom Android 4.4.2. It can‛t root.
View 1 Replies
View Related
Dec 20, 2012
How to replace the default boot splash on an Allwinner A13 tablet? I'm thinking about replacing the rather tacky default image on it, and maybe the battery charge and other bitmaps.
View 4 Replies
View Related
Apr 23, 2013
I have compiled cwm for an allwinner a13 tablet I am stuck for in for on recovery but can't do any thing it just reboots to recovery if I select reboot system and can't install backup restore.
Only adb side loading works tried to install another working old cwm it shows successfully installed but it reboots to the same recovery.
I tried to install a custom rom but first I got first error in get prop =build Id
So removed get prop lines in updater script now I am getting installation aborted status 0 error
View 3 Replies
View Related
Mar 23, 2014
I have an Allwinner A20 tv box, I trying to use it on a device with an old, low res, 4:3, 5" screen. It works but I have a few problems - firstly the box has "pal" and ntsc" settings for use with AV out, but when connected the picture is squashed inwards so circles are represented as ovals. I ve tried to mod the aspect ratio/resolution but nothing works, the picture is always distorted.
On top of that everything is too small for the screen, it is readable but things really need to appear bigger, so I also played about with the dpi, this does make things bigger and a better match for the screen, even though the device doesnt actually have a screen itself.
I ve done both these mods with several apps and modding the build prop and I always get "sorry systemGUI has stopped", constantly - when you close it, it opens again straight away. Clearly settings doesnt like these mods, so I m trying to work what I need to change so it DOES accept them.
How I can successfully mod the setting.db and get this working at the correct aspect ratio and a dpi that is suitable for use on a low res screen ?
View 1 Replies
View Related
Dec 31, 2013
I have a Nexus 7 tablet and every few days I notice a few new apps on the device. I'm not sure if they're full apps or just simply icons to download apps or get more information. I have tried to avoid using them. I know previously I had a couple apps that were sending notifications to the notification system that I considered to be spam. After some research I found out how you can find out which apps are doing it and disable notifications from those apps so that took care of that.
View 4 Replies
View Related
Jul 22, 2013
i have a chinese tablet (Teclast P98HD A2Q6) with some very good specs it has 4.1.1 but it's laggy there's another tablet called (PIPO M6) with the same processor and display & it has 4.2.2 with the latest SDK for the chip.can i upgrade my tablet with PIPO's firmware ?
View 9 Replies
View Related
May 26, 2014
I have an Allwinner A10 clone (Kurio 7), it is designed for kids but otherwise a standard android tablet. After hours of googling I rooted and installed CWM & Gapps (not included in the stock ROM). So far so good. The stock ROM was causing issues with some apps, it needed to go.
I flashed CM10 and it worked but no touch screen. It needed a compatibility flash to make it work. You can guess what's coming. I picked the wrong one and now the device does the following:
Reboot loop
Black screen (backlight though)
PWR+Vol up no longer gets to recovery
Vibrates constantly between reboots (due to wrong patch I'm guessing)
ADB picks up the device for a split second between reboots but "adb reboot recovery" does nothing. Even when using wait command. Tried "fastboot flash recovery cwm.img" after wait command, no luck. Is there anything else I can try?
View 1 Replies
View Related
Feb 1, 2013
I'm running a GOCLEVER R75 tablet. I succeeded in installing the USB drivers to Windows XP pro from the last SDK I downloaded previously.But I can't install other drivers:
C:> c:AndroidSDKadt-bundle-windows-x86sdkplatform-toolsadb devices
adb server is out of date. killing...
* daemon started successfully *
List of devices attached
Although I can see in Windows Device manager Android Phone - Android ADB Interface, some applications still write they can't see my Android device. I also can't see the tablet number.
View 4 Replies
View Related
Sep 22, 2013
I boot my Acer Iconia Tab A200 into fastboot mode (robot lying down and RED exclamation mark over it). I plug it into my Windows 7 (64bit) desktop computer with SDK installed, and from the directory with fastboot.exe I type FASTBOOT DEVICES but the device is not being seen, it just goes back to the prompt, like the command executed but didn't do anything. I assume this is because the drivers aren't installed. But I don't know how to install the "adb drivers".
View 4 Replies
View Related
Mar 2, 2013
I'm trying to use the SWM and when I have everything all set up it tells me I have no device set up. I looked to see if I could find drivers for me Xperia X10 and all I kept getting linked to was the sony PC companion that apparently had those drivers installed. When I installed it and did all the set up stuff it still wouldn't recognize my phone other than as a removable disk. I have the USB debugging turned on, .Net framework installed, and supposed the drives yet it still won't read my phone.
View 1 Replies
View Related
May 15, 2014
I take the CyanogenMod 10.3 for my Alcatel OT995, it works fine on my device, but I can't use adb command line neither other features using adb.exe ! I can only access to storage mass device, so I think I have a problem with the USB drivers which connect ADB command to my phone. I can add that before I've installed this Rom on the device, I've installed many drivers on the PC :
Firstly I installed the owner's driver provided by Alcatel in the AlcatelAndroidManager.exe package,
secondly I installed the Google USB drivers provided because I'm using Android Virtual Devices (AVD Manager) to do some developping works. I used to launch adb with "adb start-server" so it's still working, I don't obtain any device in the list with "adb devices", why don't I get it ?
I've realized some cleaning actions : I uninstalled the USB drivers of Alcatel's software, I uninstall the Google USB driver , to finish I reboot the PC but it don't changed anything I tried to apply this (well explained) post without any success :URL.... I can't find "Android devices" category, neither "Usb Adb" entry... so my device is not recognized in the "Settings Panel". However the storage mass device appears as a volume named "
View 1 Replies
View Related
Oct 10, 2012
How to do this? is this possible? if yes, where is the driver.
View 5 Replies
View Related
Sep 23, 2012
I have been trying to root my Micromax A25 but to no luck. And I have been unable to find the drivers for it.
View 2 Replies
View Related
Jun 1, 2014
i have downloaded several drivers, all are .inf format for Win764BIT because i am under Win864BIT .. but when i am trying to install the driver via device manager it says the drivers are not digitally signed .. and when i try using SP Flash Tool to test to flash stock rom to my currently working device .. it does not start, so i think it is not detected .. I am using a PH Version of CUBOT C11 (MT 6572) Device .. i can't try to make it work.
View 9 Replies
View Related
Nov 30, 2013
Windows 7 (64 bit) Dell Desktop PC and my lovely new Sony Xperia Z1 trying to send files via Bluetooth rather than keep plugging and unplugging the USB cable and risk breaking the cover. well that was my plan anyway.The Dell didn't come with Bluetooth so I bought a wee plug-in USB Bluetooth unit. I have managed to copy a couple of files but it took ages to get it to connect properly and now it won't do it at all.There are 4 driver messages under hardware which all show problems with Bluetooth peripheral device and no drivers installed, but I can't find any anywhere?
View 1 Replies
View Related
